User Tools

Site Tools


Differences

This shows you the differences between two versions of the page.

Link to this comparison view

en:produkte:cad_2016:beregnung_pruefen_und_bearbeiten [2013/06/19 11:09] (current)
Line 1: Line 1:
 +====== Check and edit Irrigation ======
 +===== Analyze water distribution =====
 +=== Description ===
 +With this function you can review the distribution of the water distribution for the proposed sprinklers and detect under- or over-supply in the diagram. For this, all sprinklers in the current irrigation project are analyzed.\\ {{:​produkte:​cad:​planung:​was037.png?​nolink|}}
  
 +=== Procedure ===
 +  - Mark the irrigation project or a Group (see [[Massenbaum]]) in the **Irrigation-Manager**.
 +  - Switch to the tab **Analysis**.
 +  - Select the button **[Add]**.
 +  - You can use the standard settings or make amendments.
 +  - Confirm the dialogue **Analysis water distribution** with {{:​produkte:​cad:​planung:​zei0116_2013.png?​nolink|}} (Apply).
 +  - Move the dialogue **Irrigation-Manager** to the side, if necessary, to review the analysis in the drawing.
 +
 +<WRAP round tip 90%>
 +If the //Colour 100%// is spread evenly over the surface the water distribution is ideal.
 +</​WRAP>​
 +
 +To optimize the distribution of the sprinkler you can **Set sprinklers** additionally (see [[Beregnung erstellen]]) and **Edit sprinklers** (see next chapter) that are already in the drawing. Refresh the analysis afterwards. ​
 +
 +<WRAP round tip 90%>
 +Use the graphic analysis for the water distribution for the presentation to the client.
 +
 +If you want to use the analysis only for control measures you can turn it off when you are satisfied with the distribution. Click on the symbol ​ {{:​produkte:​cad:​planung:​was013.png?​nolink|}} in front of the analysis.
 +</​WRAP>​
 +
 +=== Method ===
 +The water distribution analysis (Tensiogram) is based on the assumption that a single sprinkler has at the sprinkler centre a water distribution of 100% which decreases with growing distance. ​
 +
 +To achieve a coverage as uniform as possible the sprinklers should be arrayed with overlapping distribution curves so that they add up.\\ {{:​produkte:​cad:​planung:​was077.png?​nolink|}}
 +
 +<WRAP round important 90%>
 +The memory requirements increase, the more analysis are created in the drawing and the finer those analysis are. Please find more information in the section [[Registerkarten]] > Analysis.
 +</​WRAP>​
 +
 +----
 +
 +===== Edit sprinkler =====
 +=== Description ===
 +To optimize the distribution of the sprinklers you can add more and change sprinklers in the drawing.
 +
 +=== Procedure ===
 +  - Close the dialogue **Irrigation-Manager**.
 +  - Click on a sprinkler that you want to edit.
 +  - Click on a blue grip point to change angle, throwing range, orientation,​ and position of the sprinkler.
 +  - Move the cursor until the desired setting is visible and click again.\\ <WRAP round tip 85%><​WRAP column 60%>
 +{{:​produkte:​cad:​planung:​was076.png?​nolink ​ |}}
 +</​WRAP>​
 +<WRAP column 30%>
 +When editing the radius, two green circles appear near the cursor. They denote the minimum and maximum radius. Here too, a value can be entered for the radius.
 +</​WRAP>​
 +</​WRAP>​
 +  - The changes are updated in the **Irrigation-Manager**.
 +
 +<WRAP round tip 90%>
 +If a Water distribution analysis already exists it can be updated by clicking the respective button.
 +</​WRAP>​
 +
 +----
 +
 +===== Recalculate sprinklers =====
 +Start the function with Menu **Extras > Recalculate sprinklers**.
 +
 +When specifying new values for **Pressure Sprinkler** and **Pressure Nozzle** the automatically detected sprinklers are recalculated and, if required, new sprinklers are applied.
 +
 +In this process two other things are checked: ​
 +
 +  - Is there are change in the material specifications of the Pre-settings (see [[wasser Massenbaum]])?​\\ => If YES, the sprinklers will be updated and the new material specifications will be used.\\ \\ 
 +  - Are the sprinklers of a valve circuit (see [[Anschlüsse erstellen]]) suitable for this combination?​\\ => If NO, the spinklers will be substituted by suitable ones.
 +
 +----
 +
 +===== Specify height =====
 +Start the function with Menu **Extras > Specify height**.
 +
 +Since the height difference between sprinkler to water source has impact on the operating pressure the difference in height can be specified. Once the entered value is confirmed with **[OK]** it will be applied to all sub-ordinate sprinklers.
 +
 +The advantage is that the value for the difference in height to the water source has to be set only once, for example when multiple sprinklers are detected in a valve circuit and all have the difference in height to the water source.
 +
 +<WRAP round important 90%>
 +The height difference to the water source is only considered for sprinklers.
 +</​WRAP>​
 +
 +----
 +
 +===== Case-regulated pressure =====
 +Start the function with Menu **Extras > Case-regulated pressure**.
 +
 +The option **Case-regulated pressure** is especially available for the field **Sprinkler** (see [[Beregnung erstellen]] > Set sprinklers automatically). The function ensures that the sprinkler pressure is not greater than the entered value, regardless of the operating- and water-pressure.
 +
 +Once the dialogue is confirmed with **[OK]**, the entered values are applied to all sub-ordinate sprinklers. This has the advantage that the values for the pressure only have to be entered once, for example when multiple sprinklers are detected in a valve circuit and the same pressure is to be allocated to them.\\ {{:​produkte:​cad:​planung:​was083.png?​nolink|}}
 +
 +----
 +
 +===== Inherit properties =====
 +Start the function with Menu **Extras > Inherit properties**.
 +
 +Properties like caption and graphic are inherited automantically from hierarchial higher objects to the sub-objects. Exemption: The properties were defined for individual objects. This function restores the original state.
 +
 +<WRAP round important 90%>
 +Manually defined object properties will be overwritten.
 +</​WRAP>​
 +
 +----
 +
 +===== Intersecting hoses =====
 +Start the function with Menu **Extras > Intersecting hoses**.
 +
 +It can happen that hoses intersect in the design.
 +
 +In order to understand which hose overlays which the intersections are marked with a hose intersection sign.\\ {{:​produkte:​cad:​planung:​was082.png?​nolink&​200|}}
 +
 +The sign width can be amended in the **Properties** (see [[Registerkarten]]) of the irrigation project.
 +
 +<WRAP round important 90%>
 +Should you not require a sign set the value to 0.
 +</​WRAP>​
 +
 +You can **Edit** the **hose order** (see next chapter).
 +
 +----
 +
 +===== Edit hose order =====
 +Start the function with Menu **Extras > Edit hose order**.
 +
 +With the option Edit hose order you can specify later on which hose is to overlay which at an intersection.\\ {{:​produkte:​cad:​planung:​was084.png?​nolink|}}
 +
 +In the list all used hoses are displayed.\\ ​
 +You can change the order of the hoses by clicking on a hose and moving it up or down with the arrow buttons.
 +
 +<WRAP round tip 90%>
 +The hose intersection signs are adjusted automatically.
 +</​WRAP>​