User Tools

Site Tools


Differences

This shows you the differences between two versions of the page.

Link to this comparison view

en:produkte:cad_2016:anschluesse_erstellen [2013/08/15 13:58] (current)
Line 1: Line 1:
 +====== Set Connections ======
 +===== Set water connection =====
 +=== Description ===
 +The basis for the irrigation system is the water connection.
  
 +With the function Set water connection you can add a water connection (with image) to the drawing to position the water source for the irrigation project. This is done on the basis of the object`s water pressure and water quantity.\\ {{:​produkte:​cad:​planung:​was0011.png?​nolink|}}
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Water supply > Set water connection** or with the icon {{:​produkte:​cad:​planung:​was014.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Irrigation project** and start the command **Set water connection**.
 +  - Then the dialogue **New water connection** opens. ​
 +  - Enter the value for the **pressure** in the respective field.
 +  - Specify the **water quantity** (either in m³/h or l/min) for your project.\\ <WRAP round tip 85%>
 +You can edit these values and add them to the series of measurements. For this mark the entry **water source** in the left section of the **Irrigation-Manager** and select the tab **Technical Data** (see [[Registerkarten]]).</​WRAP>​
 +  - Confirm your input with **[OK]**.
 +  - Specify in the drawing a location for the water source.
 +  - The image for the water source is inserted into the drawing and the **Irrigation-Manager** opens again.
 +
 +<WRAP round tip 90%>
 +The inserted image can be edited via the blue grip points. For this the image is marked in the drawing and can be moved with the centre point or scaled with the frame point.
 +</​WRAP>​
 +
 +----
 +
 +===== Set valve unit =====
 +=== Description ===
 +Under **valve unit** the valves are assembled locally which allows a simplified maintenance of the distributor. ​
 +With the function **Set valve units** you can add valve units (with image) to the drawing to specify the position of the valve unit for the irrigation project.
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Set valve unit** or with the icon {{:​produkte:​cad:​planung:​was015.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Irrigation project** and start the command **Set valve unit**.
 +  - Specify a **location** for the valve unit in the drawing.
 +  - The image for the valve unit is inserted into the drawing and the **Irrigation-Manager** appears again.
 +
 +<WRAP round tip 90%>
 +The inserted image can be edited via the blue grip points. For this the image is marked in the drawing and can be moved with the centre point or scaled with the frame point.
 +</​WRAP>​
 +
 +----
 +
 +===== Draw pipe =====
 +=== Description ===
 +If you have already specified a water connection as well as a valve unit you can now connect those two elements with a water pipe.
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Water pipe> Draw pipe** or with the icon {{:​produkte:​cad:​planung:​was005.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Water source** and start the command Draw pipe. 
 +  - Draw a line. Click on the image with the valve unit. 
 +  - You apply the drawn pipe by clicking on the button **[Done]**. ​
 +  - In the **Irrigation-Manager** the pipe and valve unit are sorted under the water source.
 +
 +{{:​produkte:​cad:​planung:​was0013.png?​nolink|}}
 +
 +<WRAP round tip 90%>
 +You can edit pipes at a later stage by marking them in the Irrigation-Manager and then clicking on the icon **Edit** {{:​produkte:​cad:​planung:​was016.png?​nolink|}}.
 +</​WRAP>​
 +
 +=== Functions ===
 +<WRAP column 20%>
 +{{:​produkte:​cad:​planung:​was0012n.png?​nolink|}}
 +</​WRAP>​
 +<WRAP column 72%>
 +^Function^Description^
 +|**Add**|As soon as a pipe section exists you can add valve units to it. For this specify a valve unit and then the point of connection on the water pipe. The valve unit is subsequently connect to the water source with the pipe (see also **Add automatically**). |
 +|**Remove**|Releases valve units from the water pipe so that they can be connected to other water pipes.|
 +|**Add automatically**|If valve units are close to a drawn water pipe the objects will be automatically connected to the water pipe and thus the water source.|
 +|**Draw**|Draws a line through specified points and denotes the course of the pipe.|
 +|**Insert points**|Adds points between the existing points. For this, select the point before the point to be inserted first, and then specify the new points.|
 +|**Delete points**|Deletes the selected point.|
 +|**Close pipe**|The water pipe can be closed and thus used as ring line. For this select the point on the line that you want to close the pipe with.|
 +|**Undo**|Reverses the most recent action.|
 +|**Change material**|Once you have a pipe section, a change of material, E.g. to a pipe with a smaller diameter, can be defined. To do this, click the endpoint of a pipe segment (into the red square). The material change will be marked with a line. Then you can continue drawing. In the Irrigation Manager, the materials of the selected Pipe will be shown in the [[registerkarten|Tab]] **Pipe dimensions**.|
 +|**New branch**|For the current pipe a new branch can be added. For this the connection point on the pipe is selected first and then the new branch is drawn (in another colour).\\ \\ With **[End branch]** the drawing of a new branch is ended and the original course of the current pipe can be continued.|
 +|**New pipe**|Drawing the current pipe is ended (and saved) and a new pipe is started.|
 +|**Done**|Ends the drawing of the current pipe, closes the dialogue **water pipe** and displays the Irrigation-Manager again. The new objects can be found in the group **water source**.|
 +</​WRAP>​
 +<WRAP clear></​WRAP>​
 +
 +<WRAP round tip 90%>
 +The material selection of hoses/pipes for waterpipes happens automatically as soon as sprinklers are detected in a valve circle. However, this depends on the sprinkler specifications and the material database.\\ Also, the Material selection can be done manually. (see [[Materialien zuweisen]] > Select materials).
 +</​WRAP>​
 +
 +----
 +
 +===== Draw valve circuit =====
 +=== Description ===
 +Create a valve circuit and collect the therein contained sprinklers that have the same requirements for the pressure and the same spray intensity.
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Valve circuit > Draw valve circuit** or with the icon {{:​produkte:​cad:​planung:​was006.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Valve unit** and start the command **Draw valve circuit**.
 +  - Starting from the valve unit draw a line to the first sprinkler and continue on to the other sprinklers in the valve circuit. ​
 +  - Click the button **[Done]** if you want to finish the creation of the valve circuit. ​
 +  - In the **Irrigation-Manager** a new object **valve circuit** is created under the **valve unit** where the added sprinklers are sorted to automatically. ​
 +
 +<WRAP round tip 90%>
 +You can edit a valve circuit at a later stage by marking the valve circuit in the Irrigation-Manager and then selecting the icon **Edit** {{:​produkte:​cad:​planung:​was016.png?​nolink|}}.
 +</​WRAP>​
 +
 +=== Method ===
 +For every valve circuit the water consumption is displayed graphically in the dialogue **valve circuit**.\\ {{:​produkte:​cad:​planung:​was053.png?​nolink|}}
 +
 +<WRAP round important 90%>
 +The water consumption should not be greater than the available water quantiy. If this is predictable,​ create multiple valve circuits with the option Draw valve circuit.
 +</​WRAP>​
 +
 +As soon as one sprinkler is selected the sprinklers are labelled in different colours.\\ {{:​produkte:​cad:​planung:​was052.png?​direct&​300|}}
 +
 +For this a value for the **Density rectangular** bond from the tab **Technical Data** is used. This value shows the sprinklers in blue that are suitable for the combination with the selected sprinkler. Un-suitable sprinklers are displayed in red. The display for the water distribution can be deactivated in the tab **Properties** (see [[Registerkarten]]).
 +
 +When drawing valve circuits the program checks, besides an even water distribution,​ if there is sufficient pressure available. Both are displayed in the **Irrigation-Manager** as follows:\\ {{:​produkte:​cad:​planung:​was072.png?​nolink|}}
 +
 +Causes can be, eg. that sprinklers with uneven water distribution are selected or that the pressure of the water source is too low. Therefore check the specified values.\\ Please find further information in the tab **Sprinkler overview** (see [[Registerkarten]]).
 +
 +=== Functions ===
 +<WRAP column 20%>
 +{{:​produkte:​cad:​planung:​was0014n.png?​nolink|}}
 +</​WRAP>​
 +<WRAP column 72%>
 +^Function^Description^
 +|**Add**|As soon as a pipe section exists you can add sprinklers to it. For this specify the sprinkler and then the point of connection on the valve circuit. The selected sprinklers are subsequently connect to the valve cicuit (see also **Add automatically**). |
 +|**Remove**|Releases sprinklers from the valve circuit so that they can be connected to other valve circuits.|
 +|**Add automatically**|If sprinklers are close to a drawn pipe of a valve circuit the objects will be automatically connected to the valve circuit.\\ <WRAP round important 80%>
 +Drip pipes and drip pipe areas are not automatically added to the valve circuit. To do this, select the function **[Add]** (see above). Then click the drawn line of a drip pipe or the drip pipe area. After that specify the connection point on the valve circuit.
 +</​WRAP>​|
 +|**Draw**|Draws a line through specified points and denotes the course of the pipe.|
 +|**Insert point**|Adds points between the existing points. For this, select the point before the point to be inserted first, and then specify the new points.|
 +|**Delete point**|Deletes the selected point.|
 +|**Close pipe**|The valve circuit can be closed and thus used as ring line. For this select the point on the line that you want to close the pipe with. Within a ring line the pressure will be calculated so that there is less pressure lost at the end of the line.|
 +|**Undo**|Reverses the most recent action.|
 +|**Change material**|As soon as there is a section to the circle of a valve, a change of material, E.g. to a pipe with a smaller diameter, can be defined. To do this, click the endpoint of a section (into the red square). The material change will be marked with a line. Then you can continue drawing. In the Irrigation Manager, the materials of the selected valve circle will be shown in the [[registerkarten|Tab]] **Pipe dimensions**.|
 +|**New branch**|For the current valve circuit a new branch can be added. For this the connection point on the pipe is selected first and then the new branch is drawn (in another colour).\\ \\ With **[End branch]** the drawing of a new branch is ended and the original course of the current valve circuit can be continued.|
 +|**New valve circuit**|Drawing the current valve circuit is ended (and saved) and a new valve circuit is started.|
 +|**Done**|Ends the drawing of the current valve circuit and closes the dialogue valve circuit. In the dialogue **Irrigation-Manager** a new object **valve circuit** is displayed where the added sprinklers are sorted to. Every valvue circuit contains the connected sprinklers.|
 +</​WRAP>​
 +<WRAP clear></​WRAP>​
 +
 +<WRAP round tip 90%>
 +The material selection of hoses/pipes for valve circuits happens automatically. However, this depends on the sprinkler specifications and the material database. Also, the Material selection can be done manually. (see [[Materialien zuweisen]] > Select materials).
 +</​WRAP>​
 +
 +----
 +
 +===== Set field control system =====
 +=== Description ===
 +Control systems automate the operation of an irrigation system and thus the utility factor of the system increases many times.
 +
 +With the function Set field control system you can add a control unit (with image) to the drawing to specify the location of the control unit for the irrigation project.
 +
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Set field control system** or with the icon {{:​produkte:​cad:​planung:​was026.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Irrigation project** and start the command **Set field control system**.
 +  - Specify the location for the control unit in the drawing.
 +  - The image for the control unit is inserted into the drawing and the **Irrigation-Manager** appears again.
 +
 +<WRAP round tip 90%>
 +The inserted image can be edited via the blue grip points. For this the image is marked in the drawing and moved with the centre point or scaled with the frame point.
 +</​WRAP>​
 +
 +If the entry **Control units** is marked in the left section of the Irrigation-Manager the power supply can be denoted by drawing one or more cables with the option **Draw cable** (see next chapter).
 +
 +----
 +
 +===== Draw cable =====
 +=== Description ===
 +As soon as you have placed a control unit into the drawing you can draw linear connections from the control unit to the power source with this function.
 +
 +=== Procedure ===
 +Start the function with Menu **Connections > Electric cable > Draw cable** or with the icon {{:​produkte:​cad:​planung:​was027.png?​nolink|}}.
 +
 +  - Select in the left section of the Irrigation-Manager the entry **Control units** and start the command **Draw cable**.
 +  - Starting from the control unit draw a line to denote the course of the cable.
 +  - Click the button **[Done]** to end the creation of an electric cable.
 +  - In the Irrigation-Manager the electric cable will be displayed below the entry **Control unit**.
 +
 +<WRAP round tip 90%>
 +You can edit the electric cables at a later stage by marking the electric cable in the Irrigation-Manager and clicking on the icon **Edit** {{:​produkte:​cad:​planung:​was016.png?​nolink|}}.
 +</​WRAP>​
 +
 +<WRAP column 20%>
 +{{:​produkte:​cad:​planung:​was050.png?​nolink|}}
 +</​WRAP>​
 +<WRAP column 72%>
 +^Function^Description^
 +|**Draw**|Draws a line through specified points and denotes the course of the cable.|
 +|**Insert points**|Adds points between the existing points. For this, select the point before the point to be inserted first, and then specify the new points.|
 +|**Delete points**|Deletes the selected point.|
 +|**Close cable**|To close the cable select the point on the line that you want to close the cable with.|
 +|**Undo**|Reverses the most recent action.|
 +|**New branch**|For the current cable a new branch can be added. For this the connection point on the cable is selected first and then the new branch is drawn (in another colour).\\ \\ With **[End branch]** the drawing of a new branch is ended and the original course of the current electric cable can be continued.|
 +|**New cable**|Drawing the current cable is ended (and saved) and a new cable is started.|
 +|**Done**|Ends the drawing of the current electric cable and closes the dialogue **Cable**. In the dialogue Irrigation-Manager a new object **Electric cable** is displayed below the **Control unit**. |
 +</​WRAP>​